The rubber profile at its base acts as a sound break and increases the isolation efficiency in high frequencies. The housing of Vibro-AMR is designed to limit vertical and horizontal movement of the isolated equipment and offers a seismic protection.Īll the metal parts of Vibro-AMR are constructed from metal plates with adequate thickness properly formed with no welding points. On the upper part, there is an M8 bolt in order for the Vibro-AMR to be fixed to the machinery. There are two holes on the base for fixing with M8 pass-through bolts (not included). When high wind loads or other external forces are applied.When the vibrating equipment is likely to have its center of mass significantly altered.Vibrating equipment is likely to be subjected to seismic events.Vibro-AM.Restrained is recommended to be used for mechanical Noise & Vibration isolation for: They can sustain forces of the tension, compression, shear nature.Ī polyester powder paint protects the metal plates from oxidation. It can be used for low-frequency vibration control (low-speed rotation 400 rpm upwards) that also requires lateral and vertical restraint and protection from earthquakes and excess wind pressure. KSCR 3.Vibro-ΑMR Spring Isolator Mount is a multi-directional anti-vibration restraint with relative limit stops.SRH Spring and Neoprene Isolation Hanger.SFH Spring and Fiberglass Isolation Hanger.FLSS Seismic Control Restrained Spring Isolator.TITAN Modular Seismic and Wind Restraint Vibration Isolator.KCI Miami-Dade Approved Spring Isolator. Website Custom Crafted by Bright Cloud Studio. Vibration isolators shall be Model FLS as manufactured by Kinetics Noise Control, Inc. Springs shall be color coded or otherwise identified to indicate load capacity. Springs shall be selected to provide static deflections shown on the Vibration Isolation Schedule or as indicated on the project documents. Non-welded spring elements shall be polyester powder coated, and shall have a 1000 hr rating when tested in accordance with ASTM B-117. Spring elements shall have a lateral stiffness greater than 1.2 times the rated vertical stiffness and shall be designed to provide a minimum of 50% overload capacity. Housing should be designed to provide a constant free and operating height within 1/8" (0.06 mm). Housing shall be electrozinc plated or hot dip galvanized for corrosion resistance. Housing assemblies shall be fabricated steel members and shall consist of a top load plate complete with adjusting and leveling bolts, vertical restraints, isolation washers and a bottom plate with internal non-skid noise isolation pads. Vibration isolators for equipment which is subject to load variations and large external or torquing forces shall consist of large diameter laterally stabile steel springs assembled into welded steel housing assemblies designed to limit vertical movement of the supported equipment. Kinetics Model FLS spring isolators are recommended for the isolation of vibration producing equipment carrying a large fluid load which may be drained, such as boilers, cooling towers and chillers, and for the isolation of outdoor components such as cooling towers, air-cooled condensers, etc., where wind loads are minimal. Custom isolators with higher deflection and greater load capabilities are available. FLS Springs are available with deflections to 4" (102 mm) and with load capacities to 23,200 lbs. To assure stability, the springs have lateral spring stiffness greater than 1.2 times the rated vertical stiffness, and are designed to provide a minimum of 50% overload capacity. The isolator can be welded to the structure as well. Holes are provided in all isolators for bolting to the structure and to the supported equipment. Springs are polyester powder coated, with a 1000-hour salt spray rating per ASTM B-117. Spring elements are complete with internal noise isolation pads and have an adjusting and leveling bolt as a part of the top load plate assembly. The housings also provide a constant free and operating height to facilitate installation. Kinetics Model FLS vibration isolators consist of free-standing, large diameter, laterally stable steel springs assembled into welded steel housing assemblies fabricated to limit vertical movement of the isolated equipment if equipment loads are reduced, or if the equipment is subjected to large vertical external forces. KINETICS® FLS-1 & FLS-2 Restrained Spring Isolators
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |